Afx FUV225SNMV User Manual download pdf

FUV Fluorescent Vanity Fixture

Model 217, 225, 232

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

Make sure that the power source conforms to the requirements of the

fixtures. (See labels on the fixture housing). Dimming controls

cannot be used with multi-volt (120-277 VAC) ballasts.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel. The green ground

screw location is clearly marked on the fixture housing.

This fixture is intended to be used for general indoor lighting in dry

or damp locations only.

Assembly Instructions

1. Preparing for installation

A. Disconnect electrical power before installing or servicing any part of this fixture.

B. Remove wire way cover (7) by squeezing along channel (6).

C. Remove the appropriate knockout(s) for power supply entry.

D. (Model FUV232 only) Install center diffuser support (4) with knurled

thumbscrews (3) provided. Tighten before mounting.

2. Fixture mounting.

A. To locate, hold channel (6) up to the wall with power supply knockout located

over entryway for power supply wires. Mark the locations of the mounting holes

on the wall. Take the channel down and punch a small hole into the wall at each

location using a nail or an awl to see if there is a wood joist. If there is a joist use a

suitable wood screw (not included) to mount the channel. Where there is no joist

to screw into use a toggle bolt (not included) of suitable length to mount channel

securely to the wall. Proceed to step B before final mounting.

B. Feed the black and white supply wires, and the green ground wire into the fixture

through the open knockout hole. At this time you can finish mounting the channel

to the wall.

3. Wiring.

Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If power supply wires are within

three inches of ballast use wire suitable for at least 90C (194F). Note: Most dwellings built before 1985 have supply wire rated to 60C. Consult

a qualified electrician before installing.

A. This unit will not operate properly unless connected to a “grounded” electrical circuit. Electrical shock, over heating, low or no light

output, and shortened lamp life can result if proper grounding is not done. Securely attach green (or green and yellow) wire to provided

green ground screw.

B. Using luminaire disconnect (provided), insert white supply wire into the hole across from white ballast lead. Insert black hot supply wire

into hole across from black ballast lead. Do not mix wires. Pull on each wire to make sure connections are secure. Make certain no bare

wires are exposed outside of luminaire disconnect.

C. Install wire way cover (7) by laying one edge down and around edge of channel (6) then snap opposite edge of cover down and around

edge of channel.

D. Install appropriate lamp(s) (5) (not included) by inserting lamp pins into lamp holder. Rotate into place to seat lamp for proper connection.

4. Diffuser mounting.

A. Models FUV217, Install one end cap (1) with provided ball nut (8). Install diffuser (2) into end cap (1). Install second end

cap (1) and secure with ball nut (8).

B. Model FUV232 & FUV225, Position one diffuser (2) into center mounting bracket (4), hold securely and install end cap (1)

with decorative ball nut (8) provided. Repeat procedure for second diffuser.

Power to the fixture can now be restored.

Limited Factory Warranty

American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating

conditions for a period of 2 years from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective fixture or

components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

Page 1 of 1 8060083-Rev2

Safety Precautions 1

Summary of Contents

Page 1 - Safety Precautions

FUV Fluorescent Vanity Fixture Model 217, 225, 232 Safety Precaution

Related models: FUV232SNMV | EOV217RBR8 |

Comments to this Manuals

No comments

Afx FUV225SNMV User Manual

Browse online or download User Manual for Lighting Afx FUV225SNMV. AFX FUV225SNMV User Manual

Summary of Contents

Related models: FUV232SNMV | EOV217RBR8 |

Comments to this Manuals

Related products and manuals for Lighting Afx FUV225SNMV