Afx DEP126SNEC User Manual download pdf

DEP Series Fluorescent Pendant Fixture

Model 126

Page 1 of 1 8060539 Rev 1

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that all wiring be performed by a qualified

electrician. This fixture must be wired in accordance with all national

and local electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

This fixture is designed for use in a 110-120VAC, 60Hz fused circuit.

Do not use on a dimming circuit.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. Make sure to connect the

canopy (8) ground wire to the incoming earth ground from your main

power supply panel.

This fixture is intended to be used for general indoor lighting in dry

locations only.

Assembly Instructions

1. Preparing for installation.

A. Disconnect electrical power before installing or servicing any part of this fixture.

B. Insert one set of #8-32 x 1-1/2 screws (9) through the top of gem bar (10) with the

threaded portions facing down to line up with the mounting holes in the canopy (6).

C. Attach gem bar (10) to junction box (not provided) in position shown with #8-32 x 1-1/2

screws (8) provided. Note: Allow access into junction box to complete wiring.

Wiring

All wiring must take place inside junction box. Caution: Make sure power is off at fuse or

circuit breaker box. Check power wires for damage or scrapes. If power supply wires are

within three inches of ballast use wire suitable for at least 90C (194F). Note: Most dwellings

built before 1985 have supply wire rated to 60C. Consult a qualified electrician before

installing.

A. Feed cord (4) through strain relief (7) and center hole in canopy (6).

B. Connect the green ground pig-tail wire attached to the canopy to the supply ground wire

and secure with a wire nut (11).

C. To modify cord length, unscrew strain relief cover (7) from canopy (6). Pull cord (4)

through canopy to desired length. Secure cord by re-attaching strain relief cover.

D. Determine desired cord (4) length for fixture.

E. Once desired mounting length is determined, cut cord allowing for 6 inches of wire for

junction box wiring. Carefully remove outer insulation from cord without damaging lead

wires. Strip lead wires back 3/8 inch for wire nut connections. WARNING: Inspect

modified cord and wires for any damaged insulation.

F. Using wire connectors (11) provided, connect white (Common/Neutral) supply wire to

one clear fixture lead. Connect black (Hot/Incoming) supply

wire to the other clear fixture lead. Pull on each wire lead to

make sure connections are secure. Make certain no bare wires

are exposed outside of wire connectors.

Mounting

A. Tighten gem bar mounting screws (8).

B. Align canopy (6) over mounting studs (9) and fasten with

thumbnuts (5).

C. Tighten strain relief cover (7) to set desired length of cord (4).

4. Lamping/Re-lamping

A. Lift decorative cap (2) and glass diffuser (1) up to expose lamp-holder (13). Install appropriate 26

watt 4-pin fluorescent quad lamp G24q-3 (14) into barrel ballast (12), then install the barrel ballast

with lamp onto the socket (13) by aligning pins and turning clockwise until it stops. Carefully slide

glass and decorative top down to diffuser stop (3).

B. Restore power at fuse or circuit breaker box.

Limited Factory Warranty

American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating

conditions for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it

does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

Fluorescent Pendant Fixture 1

Summary of Contents

Page 1 - Fluorescent Pendant Fixture

DEP Series Fluorescent Pendant Fixture Model 126 Page 1 of 1

Comments to this Manuals

No comments

Afx DEP126SNEC User Manual

Browse online or download User Manual for Lighting Afx DEP126SNEC. AFX DEP126SNEC User Manual [en]

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Afx DEP126SNEC